Kategorier

More information

Tascam ML-32D

Tascam ML-32D

Tascam kommer her med et profesjonelt lyd-interface med 32 balanserte analoge inn- og utganger, som overfører digitalt til Dante-protokollen og gir 32 inn- og utganger i inntil 96kHz via en enkel, standard nettverkskabel. Da trenger du bare en lisens (til ca 270 kroner) for et DVS (Dante Virtual Soundcard), så har du et supert og profesjonelt lydkort med superlav latency til opptak eller live-streaming.

NB! Er på sentrallager og sendes derfra. Beregn 3-5 dagers leveringstid.

Lagerstatus: På lager

kr 21 050,00
ELLER

Detaljer

ML-16D and ML-32D are compact, high-quality analogue-Dante-analogue converters designed to transfer 16 or 32 analogue audio channels over a Dante network in both directions. Space-saving 25-pin D-sub connectors are provided for use with optional breakout boxes to input and output balanced, line-level analogue audio signals. Two Ethernet connectors (Dante Primary/Secondary) are available for redundant operation using two separate networks.

The units feature indicators for operation status and current sample rate as well as overload LEDs for each input and signal LEDs for each input and output. Switches on the rear side allow the user to set the required maximum input/output level. Any other settings, such as sampling frequency, channel routing or latency, can be made by the freely available “Dante Controller” computer application.

Dante is a network technology by Audinate offering high-performance audio distribution over standard IP networks. It supports hundreds of simultaneous channels of uncompressed audio with ultra-low latency and accurate synchronization.

Link til Dante Virtual Soundcard.

About Dante:
The Dante protocol was developed to provide uncompressed, multi-channel, low-latency digital audio over a standard Ethernet network aupporting as many as 1024 channels of 32b bit/192kHz audio over an existing CAT 5/6 Ethernet system.

Since inception, Dante has seen steady adoption by a growing number of systems integrators, especially those specializing in AVB (Audio Video Bridging). In addition, Dante continues to gain a foothold in the live sound arena, with hundreds of hardware products from various manufacturers supporting this innovative communications protocol. These live sound applications include: House of Worship (HOW), institutional installations, theaters, audio for stadiums and other public facilities and broadcast.

Features:

  • Ÿ  Dante focused interface for connection of external audio into or out of a Dante audio network
  • Ÿ  16 channel analog line input and 16 analog line outputs (48kHz/96kHz) using 4 D-Sub connectors
  • Ÿ  Dual redundant Ethernet jacks which support both primary and secondary connections
  • Ÿ  Up to 24 bit/96kHz quality
  • Ÿ  LED display for signal level and overload per input/output channel
  • Ÿ  Reference level dip switches for selectable DBu level metering
  • Ÿ  Firmware updatable via Dante port
  • Ÿ  AES67 and Revenna compatible

Teknisk informasjon

Ratings
Audio resolution   44.1/48/88.2/96 kHz, 16/24 bit
Analogue audio inputs
Connectors   D-sub 25-pin
Locking screws   No. 4-40 UNC (inch type)
Nominal input level   +4 dBu, +6 dBu (only when maximum input level is +15 dBu)
Maximum input level   +24 dBu, +22 dBu, +20 dBu, +18 dBu, +15 dBu
(set by REF. LEVEL switches)
Input impedance   ≥10 kΩ
Analogue audio outputs
Connectors   D-sub 25-pin
Locking screws   No. 4-40 UNC (inch type)
Nominal output level   +4 dBu, +6 dBu (only when maximum output level is +15 dBu)
Maximum output level   +24 dBu, +22 dBu, +20 dBu, +18 dBu, +15 dBu
(set by REF. LEVEL switches)
Output impedance   ≤200 Ω
Applicable load impedance   ≥2 kΩ
Network inputs/outputs
Dante PRIMARY/SECONDARY   RJ-45 connectors
  Transmission protocol   Dante
  Network standard   Gigabit Ethernet, 1000BASE-T (IEEE 802.3ab)
  Cable requirements   Cat 5e or better STP cables
Audio performance
ANALOG IN to DANTE OUT
  Frequency response   20 Hz – 20 kHz, +0.1 dB / –0.5 dB
(–16 dBFS input, 44.1/48 kHz sampling frequency, JEITA)
20 Hz – 40 kHz, +0.1 dB / –0.5 dB
(–16 dBFS input, 88.2/96 kHz sampling frequency, JEITA)
  Distortion (THD+N)   ≤0.001 %
(–1 dBFS input, 1 kHz, 44.1/48/88.2/96 kHz sampling frequency, JEITA)
  S/N ratio   ≥113 dB
(44.1/48/88.2/96 kHz sampling frequency, JEITA)
  Crosstalk   ≥115 dB
(1 kHz, 44.1/48/88.2/96 kHz sampling frequency, JEITA)
DANTE IN to ANALOG OUT
  Frequency response   20 Hz – 20 kHz, +0.1 dB / –0.5 dB
(–16 dBFS input, 44.1/48 kHz sampling frequency, JEITA)
20 Hz – 40 kHz, +0.1 dB / –1.0 dB
(–16 dBFS input, 88.2/96 kHz sampling frequency, JEITA)
  Distortion (THD+N)   ≤0.001 %
(–1 dBFS input, 1 kHz, 44.1/48/88.2/96 kHz sampling frequency, JEITA)
  S/N ratio   ≥110 dB
(44.1/48/88.2/96 kHz sampling frequency, JEITA)
  Crosstalk   ≥115 dB
(1 kHz, 44.1/48/88.2/96 kHz sampling frequency, JEITA)
Power supply and other specifications
Power supply   AC 100–240 V, 50/60 Hz
Power consumption   ML-32D: 22 W
ML-16D: 14 W
Dimensions (W × H × D)   483 mm × 45 mm × 304 mm
Weight   ML-32D: 3.5 kg
ML-16D: 3.3 kg
Operating temperature range   0–40 °C

Du er kanskje også interessert i følgende produkt(er)