Kategorier

More information

Tascam MM-2D-X

Tascam MM-2D-X

Tascam MM-2D er en to-kanals analog til Dante-konverter med innebygget mikser og lydprosessering. Tascam MM-2D er normalt bestillingsvare, så beregn tre til fem dagers leveringstid. Denne modellen leveres med XLR-kontakter. Med den medfølgende programvaren DCP Connect gjør du alle dine innstillinger og justerer lyden akkurat slik du vil ha den.

Lagerstatus: På lager

Vanlig pris kr 6 790,00

Tilbud kr 5 649,00

ELLER

Detaljer

The MM-2D is an exquisite analogue input/output unit that can either convert two mic/line input signals into two Dante output signals, or two Dante input signals into two line output signals. In addition, it also supports four-channel Dante input/output as well, making it possible to use virtually any audio sources within an established Dante network. Available with Euroblock (MM-2D-E) or XLR (MM-2D-X) connectors for analogue inputs and outputs, this model can be used for a wide range of applications.

The MM-2D is part of the Tascam Dante Compact Processor Series consisting of compact, half-rack size audio converters for Dante/AES67 networks. The models easily add additional mic/line or AES/EBU inputs/outputs to Dante audio networks in public facilities, broadcasting stations, recording studios or upmarket domestic environment and can be freely combined. A key advantage of the product range is the DSP processor built into each unit. By providing not only mixing functions and EQ but also dynamic processing, automatic level control, auto-ducking, routing and noise compensation, even small systems can fully perform without additional signal processing or mixing devices.

From the input of microphone signals to the output of powered speakers or recording devices, the Dante Compact Processor Series can build up a complete small system on their own. Remote control is possible via two different software applications available for Mac, Windows, iOS and Android devices: Tascam DCP Connect for configuration and Tascam EZ Connect for end users, both of which are simple to use and included with the units. The MM-2D also offers the possibility to mute its inputs and control its output levels via GPI. All models can be powered by PoE or an optional AC adapter. By using power daisy-chaining, two units mounted side-by-side in a rack can be powered by one AC adapter.

  • Two balanced mic/line inputs with 48 V phantom power
    Two balanced line outputs
    Two product variants:
  • MM-2D-E: Equipped with Euroblock connectors for permanent installation
    MM-2D-X: Equipped with XLR connectors for touring and other more flexible applications

Dante interface allows audio signals to be transferred over an Ethernet network

  • Two LAN connectors for Dante daisy-chaining
    Flexible routing with ”Dante Controller” software
    AES67 is supported to allow connection with Ravenna and other compatible audio network technologies
  • Up to 96 kHz sampling rate and 24 bit resolution
    Front-panel indicators for operation status and current sample rate
    Overload indicators for analogue input signals
    Signal indicators for analogue input and output signals
    Inputs can be muted by GPI (MM-2D-E only)
    Output levels can be controlled by GPI (MM-2D-E only)
    Power supply by PoE (Power over Ethernet) or optional PS-P1220E AC adapter
    Power daisy-chaining allows two units to be supplied from one AC adapter
    Half-rack size chassis (1U)
    Attachment brackets included for mounting the unit under a table top, for example

 

 

Teknisk informasjon

General
Number of channels and formats   2 channels, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 16/24 bit
Audio inputs and outputs
Analogue inputs (ANALOG IN)   MM-2D-E: Balanced Euroblock connectors, 3.81 mm pitch
MM-2D-X: XLR connectors
(XLR-3-31, 1: GND, 2: HOT, 3: COLD)
  Minimum input level   –74 dBu
  Maximum input level   +26 dBu
  Input impedance   ≥2 kΩ
Analogue outputs (ANALOG OUT)   MM-2D-E: Balanced Euroblock connectors, 3.81 mm pitch
MM-2D-X: XLR connectors
(XLR-3-32, 1: GND, 2: HOT, 3: COLD)
  Nominal output level   +4 dBu (Ref(D) ≠ –9 dBFS)
+6 dBu (Ref(D) = −9 dBFS)
  Maximum output level (selectable)   +15 dBu (Ref(D): –9 dBFS)
+18 dBu (Ref(D): –14 dBFS)
+20 dBu (Ref(D): –16 dBFS)
+22 dBu (Ref(D): –18 dBFS)
+24 dBu (Ref(D): –20 dBFS)
  Output impedance   ≤200 Ω
Note: 0 dBu equals 0.775 Vrms
Other inputs and outputs
Dante/Ethernet connectors (DATA/DATA+PoE)   RJ-45
  Transmission protocol   Dante
  Gigabit Ethernet standard   1000BASE-T (IEEE 802.3ab)
  Cable requirements   Cat 5e or better STP cables
External muting control (LED/SWITCH/GND, MM-2D-E only)   Balanced Euroblock connectors, 3.81 mm pitch
LED connectors
  Output format   Open collector (10 Ω output impedance, 48 V withstand voltage, 35 mA maximum current)
  Maximum output voltage for Low level   0.5 V
SWITCH connectors
  Maximum input voltage   5.5 V
  Minimum input voltage for High level   2.31 V
  Maximum input voltage for Low level   0.99 V
Output level control (10V/CONTROL/GND, MM-2D-E only)   Balanced Euroblock connectors, 3.81 mm pitch
Connect a variable resistor here (10 kΩ recommended)
Audio performance
Microphone input to Dante output
  Mic amp EIN (equivalent input noise)   ≤–125 dB
(150 Ω, 22 kHz LPF, A-weighted, JEITA)
  Frequency response   20 Hz – 20 kHz, ±0.5 % (sampling frequency 44,1/48 kHz, JEITA)
20 Hz – 40 kHz, ±0.5 % (sampling frequency 88,2/96 kHz, JEITA)
  Distortion (THD+N)   ≤0.005 %
(−1 dBFS input, 44.1/48/88.2/96 kHz sampling frequency, JEITA)
  S/N ratio   ≥105 dB
(44.1/48/88.2/96 kHz sampling frequency, JEITA)
  Crosstalk   ≥100 dB
(44.1/48/88.2/96 kHz sampling frequency, JEITA)
  Dynamic range   ≥105 dB
(44.1/48/88.2/96 kHz sampling frequency, JEITA)
Dante input to Line output
  Frequency response   20 Hz – 20 kHz, ±0.5 % (sampling frequency 44,1/48 kHz, JEITA)
20 Hz – 40 kHz, ±0.5 % (sampling frequency 88,2/96 kHz, JEITA)
  Distortion (THD+N)   ≤0.005 %
(−1 dBFS input, 44.1/48/88.2/96 kHz sampling frequency, JEITA)
  S/N ratio   ≥105 dB
(44.1/48/88.2/96 kHz sampling frequency, JEITA)
  Crosstalk   ≥100 dB
(44.1/48/88.2/96 kHz sampling frequency, JEITA)
  Dynamic range   ≥105 dB
(44.1/48/88.2/96 kHz sampling frequency, JEITA)
Note: JEITA indicates compliance with JEITA CP-2150
Power supply and other specifications
Power supply   PoE class 0
Tascam PS-P1220E AC adapter (sold separately)
Power consumption   6 W
Dimensions (W × H × D)   214 mm × 45 mm × 136 mm (including protrusions)
Weight   885 g

Du er kanskje også interessert i følgende produkt(er)